Powermatic 201HH Manual do Utilizador

Operating Instructions and Parts Manual 22-inch Planer Models 201 and 201HH WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergn

10Opening Hood To open the hood for access to the cutterhead, remove the two hex screws with the 22mm wrench provided. See Figure 7. Knife Installat

117. Rotate the cutterhead using the belt or pulley, and repeat steps 2 through 6 for each of the remaining three knives. 8. When all four knives

12The Planer’s Feed System (Refer to Figure 11) 1. Anti-kickback fingers 2. Infeed roller 3. Chipbreaker 4. Cutterhead 5. Pressure bar 6. Outfeed rol

136. If it is not 1/16” below the knife, correct by loosening the hex nut and turning the adjustment screw (A, Figure 14) with a hex wrench. 7. Mo

14Outfeed Roller The outfeed roller is of smooth, one-piece construction to help avoid marring the finished surface of the material being cut. It is

155. If the gauge reading is greater or less than zero, reach beneath the table with a wrench and loosen the hex nut (C, Figure 17) which is above th

16Operating Controls The stop button is a mushroom style button which is convenient for “emergency” shutdowns. After being pushed, the stop button re

17Snipe Some amount of snipe may be inevitable with many planer operations, but proper planer adjustments can so minimize snipe as to make it negligi

18 Never attempt pressure bar adjustment while planer is connected to power. Feed restriction can also occur due to pitch buildup on the table. Be s

19Troubleshooting: Planer Operating Problems Trouble Probable Cause Remedy Snipe. Table rollers not set properly. Adjust table rollers to proper he

2 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Au

20Troubleshooting: Mechanical and Electrical Problems Trouble Probable Cause Remedy Uneven depth of cut side to side. Knives not set correctly. Mak

21Trouble Probable Cause Remedy Machine will not start/restart or repeatedly trips circuit breaker or blows fuses. (continued) Starter or motor fail

22Parts List: Base Assembly Index No. Part No. Description Size Qty 1 ... 6012068 ...Rubber Boot ...

2321 ... 6292745 ...Key ...5 x 5 x 16 ... 2 2

24 Gearbox Assembly

25Parts List: Gearbox Assembly Index No. Part No. Description Size Qty ... 201-100...Gearbox Assembly ...

26Column Assembly

27Parts List: Column Assembly Index No. Part No. Description Size Qty 1 ... 6012193 ...Lifting Eye ...

28Table Assembly

29Parts List: Table Assembly Index No. Part No. Description Size Qty 1 ... 6012233 ...Bracket ...

3 Table of Contents Warranty and Service...

30Parts List: Top Cover Assembly Index No. Part No. Description Size Qty 1 ... 6012181 ...Dust Hood ...

31Cutterhead Assembly

32Parts List: Cutterhead Assembly Index No. Part No. Description Size Qty 1 ... 6012131 ...Socket Head Cap Screw ...

3358 ... 6012180 ...Gib Screw * ... 32 59

34Electrical Connections – 1 Phase, 230 Volt

35Electrical Connections – 3 Phase, 230 Volt

36Electrical Connections – 3 Phase, 460 Volt

4 Warning 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings posted on

5 19. Make your workshop child proof with padlocks, master switches or by removing starter keys. 20. Give your work undivided attention. Looking ar

6 Introduction This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for a Powermatic

7 Receiving Open shipping crate and check for shipping damage. Report any damage immediately to your distributor. Read the instruction manual thoroug

8 Installing Dust Hood Mount the dust hood with the eight M6 x 10mm hex screws, eight spring washers, and eight flat washers. See Figure 3. It is st

9 Inspection Before putting power to the machine, check that all screws are tight, that all mechanical functions work freely and that the cutterhead