Powermatic 54HH Manual do Utilizador

Operating Instructions and Parts Manual 6-inch Woodworking Jointer Models 54A and 54HH 54A (1791279DXK) serial # 8040543557 and up 54HH (17

10Installing Fence to Bed Referring to Figure 5: 1. Before moving the fence assembly, secure the tilt lock handle (K). Secure the tilt lock handle

114. Pull down on the motor to achieve the desired belt tension. The V-belt is properly tensioned when finger pressure on the belt half way between

Electrical Grounding Instructions This jointer must be grounded while in use to protect the operator from electric shock. In the event of a malfunctio

13 Extension Cords Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the cu

14 Fence Stop Adjustments Periodically check the 90° and 45° backward (135°) tilt accuracy of the fence with an angle measuring device, such as an ad

15 Infeed Table Height Adjustment Refer to Figures 16 – 18. Initial (Coarse) Adjustment: 1. Loosen the rear thumb screw (D) and the lock knob (B). 2

16 Table Gib Adjustment The infeed and outfeed table gibs on your machine are factory adjusted and initially should not require re-adjustment. After

17 If the apex of the knife number one comes below the straightedge (a gap exists) or pushes the straightedge up, proceed with the following steps:

18 2. Carefully number each blade with a marker to make them easier to differentiate. 3. Place a straightedge across the outfeed table extending it

19 14. Verify that the knife is still in adjustment (steps 4 and 5). 15. Tighten the gib lock screws. 16. Repeat this entire procedure for the remai

2Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Servi

20 Setting Knives for Rabbeting and Nicks (Model 54A only) NOTE: Rabbeting is not applicable on helical cutterhead models. To position the knives for

21 Determining Correct Table Height The Outfeed Table Height Adjustment section tells you how to set the correct table height with respect to the cut

22 Operating Controls 1. Outfeed Table Height Adjust Hand Wheel 2. Outfeed Table 3. Cutter Guard 4. Fence Adjustment Handle 5. Fence 6. Infeed Tabl

23 Basic Operations Before making any cuts on the stock, make a few practice cuts by raising the infeed table to "0" and with the power dis

24 Surfacing The purpose of planing on a jointer is to produce one flat surface. The other side can then be milled to precise, final dimensions on a

25 Beveling Beveling an edge is the same operation as edge jointing, except that the fence is tilted to a specified angle.  Make certain that the ma

26 Figure 42 Rabbet Cuts (Straight Knife only) IMPORTANT: Rabbeting can be done with the straight knife cutterhead only; it is not applicable with t

27 Cutterhead Removal The entire cutterhead assembly may be removed for cleaning or for bearing and blade replacement. Some woodworkers keep a spare

28 11. Carefully remove the cutterhead (A, Fig. 48). 12. Before placing the new cutterhead back into the casting, thoroughly clean the "saddle&

29 Troubleshooting Mechanical and Electrical Problems Trouble Probable Cause Remedy No incoming power. Verify unit is connected to power, on-button i

3Table of Contents Warranty and Service ...

30 Stand – Parts List (All Models) Index No. Part No. Description Size Qty. ... 6296131...Stand Assembly ...

31 Stand –Assembly (All Models) POWERMATIC

32 Bed – Parts List (All Models) Index No. Part No. Description Size Qty. 1... 6296086...Base Slide...

33 Bed – Parts List (All Models) Index No. Part No. Description Size Qty. 58... 6285893...Washer...

34 Fence – Parts List and Assembly (All Models) Index No. Part No. Description Size Qty. ... 6296130...Fence Assemb

35 Cutterhead – Parts and Assembly (model 54A only) Index No. Part No. Description Size Qty. ... JJ6CSDX-CA ...Cutterhead A

36 Cutterhead – Parts and Assembly (model 54HH only) Index No. Part No. Description Size Qty. ... PM54HH-CA...Cutterhead A

37 Wiring Diagrams Wiring Diagram – Serial # 05060540312 and lower WHITEBLACKBLACKWHITEGREENGREENGROUNDSerial # 05060540312 and lower300MFD 125 VACE

38 Wiring Diagram – Serial # 05060540313 and higher

39

4 Warnings 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings poste

40 WMH Tool Group, Inc. 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.powermatic.

5 20. Keep visitors a safe distance from the work area. Keep children away. 21. Make your workshop child proof with padlocks, master switches or b

6Familiarize yourself with the following safety notices used in this manual: This means that if precautions are not heeded, it may result in minor i

7Introduction This manual is provided by WMH Tool Group, Inc., covering the safe operation and maintenance procedures for the Powermatic Model 54A an

8Unpacking Upon delivery, open shipping containers and check that all parts are in good condition. Any damage should be reported to your distributor

9Assembly Unpacking and Cleanup Locate the jointer in an area that is level and provides a solid foundation. Make sure that any potential kickback is